Oval Gear Meter Diesel Fuel Gasoline Kerosene Oil Flow Meter
200 Set/Sets per Month
Packaging & Delivery
Carton of Electronic Oval Gear Meter Diesel Fuel Gasoline Kerosene Oil Flow Meter
Dalian or optional
OGM Digital Fuel Diesel Flow Meter Electronic Oval Gear Meter Diesel Fuel Gasoline Kerosene Oil Flow Meter
Introduction of OGM Digital Fuel Diesel Flow Meter
The product control panel is designed with modular design, with complete functions, simple structure, convenient operation and so on. Can be widely used in petroleum, chemical, pharmaceutical, transportation, food industry and commerce. The screen is a digital liquid crystal display, the screen is divided into three lines: the top line is regarded as the current measurement data, the next line of the cumulative data.
Min Flow L/min
Max Flow L/min
Max working pressure
Key Opertion Instruction
1.. On the left CLEAN key, starting and cleared, in the middle of the START key, set up, the right for the TOTAL key, the total amount of display and class total display
2, start: press ON/CLEAN key to boot, or the sensor has a measurement pulse, can be switched on. The machine automatically shut down 4-5 minutes without any operation..
3 view total: in the normal display state press TOTAL key, the screen display TOTAL, the following row of figures is the total cumulative. 10 seconds after the automatic return to normal display.
4 when the data is clear, in the normal state of the display, press ON/CLEAN to clear when the data.
5 clear class total: in the normal display state press TOTAL button, when the screen display TOTAL, the following row shows the figure is the total cumulative, press TOTAL key again, showing a total flash, then press ON/CLEAN button to clear the value, return to normal after 3 seconds.
6. Adjustment coefficient in the normal state, not counting pulse, waiting for 5 seconds, press the start button to keep 5 seconds, entering coefficient adjustment mode, this row display has some coefficient, a flashing. Press ON/CLEAN button to 'Add', press TOTAL key to 'minus', according to the START shift, after modification, long press START wait for 1 seconds, save the revised value, and return to normal display. If you do not operate, after 30 seconds will automatically return to normal display. The modification is based on the actual measured value and display value, the actual value divided by the display value, and then multiplied by the existing coefficient is to modify the value of the. Simple generalization: when the system is large, the relative oil will be reduced. System to minor. Oil will increase.
The measuring of the Digital oval gear flowmeter is mainly composed of two mutual meshing gears, the shell and the electronic parts, as shown in Figure:
1. flow meter installed in the oil pump outlet, if installed in the inlet, the filter pressure is damaged, so that the negative pressure of the pump increases, so that the flow meter is not accurate, the pump inlet and outlet also need to be completely sealed, otherwise it will make the flow meter is not accurate.
2. in front of the flow meter should be installed in the filter, do not make more than 0.2MM particles through, to prevent the flow of particles from the particle surface stuck or blocked. Filters should be cleaned regularly.
3. In front of flowmeter should be equipped with one-way valve and the pipeline liquid flows in only one, to prevent reverse gear meter, or idling inaccurate measurement of flowmeter.
4. meter should be installed correctly, the meter display screen should be 90 degrees upward or sideways installation, not installed.
5. flow meter installation direction should be the same as the direction of the arrow on the shell body, the same direction of the liquid, the installation position should pay attention to facilitate reading.
6. flow meter pressure loss is proportional to the liquid flow, the liquid viscosity increases, and the pressure loss increases.
Calibration error coefficient
In standby mode or current charging status, press START key for 5 seconds to enter the state of the error coefficient. In the middle of a row in front of the E- and the last bit of the digital flash display, press START button, digital shift, (flashing digital displacement), press CLEAR button to "add", press TOTAL button for "minus" to modify the current flicker bit value.. This coefficient increases when the amount of oil is reduced, the smaller the coefficient is, the more oil the oil is. 5 seconds to end the error coefficient calibration. Return to display the current charging status. After calibration of the error coefficient, the new measurement pulse input is used to calibrate the error coefficients. Error coefficient calibration range: 0 - 20000. The error of the flow meter and the oil is about 0.05%.
Our company is specialized in the manufacture and supply of flow meter and flow measurement devices. We can supply a wide range of flow meters from simple low cost of variable area flow meters to high accuracy Turbine andelectromagnetic flow meter types. We manufacture and Stockhold liquid flow meters, solid flow meter and gas flow meter types including waterelectromagnetic flow meters in many sizes. We can offer flow meters for many applications such as fuel flow meter, oil flow meter, diesel flow meter phosphate ester, water, water-based fluids, air other compressed gas and petrol flow meter type. With our chemically resistant, high accuracy digital flow meter designs with pulse outputs, we can handle almost any fluid. For hazardous areas turbine meters can be supplied with ATEX Intrinsically safe pick off coils. We have a large range of secondary display instrumentation to choose from with flow rate, total flow throughput, retransmission, batching and scaled pulse option, etc. Electromagnetic flow meters are available in full bore and insertion type designs. The displays on these can show both flow rate and flow total. We are experts in the selection and supply of flow measurement equipment and any type of flow meter can be specified and supplied. We also stock hold hundreds of low cost all plastic variable area types for quick delivery. They are available with low/high flow switches and transmitters. We are well placed to provide many types of instruments on very short lead times. With shipments of most meters in 2-5 days our "promise to ship" rate is at 99.5%.